Training Programme
EMEA Training Courses
SOLiD EMEA offer a number of training courses tailored towards our customers and associated neutral host providers and system integrator contractors.
SOLiD EMEA offer a number of training courses tailored towards our customers and associated neutral host providers and system integrator contractors. Each course can accommodate up to a maximum of 8 individuals if face to face or 15 individuals remotely. The following list details if a course is face to face or can be conducted remotely. Whether you are deploying for the first time, looking to refresh your knowledge, or hoping to gain a deeper understanding of the GENESIS™ Portfolio, our courses are designed to give individuals the skillsets and understanding needed to successfully deploy a SOLiD solution. Given the technical nature of our equipment portfolio, it is assumed those individuals attending have a working understanding of RF over fibre and RF best practice fundamentals, before enrolling on these courses.
For further details on pricing and availability please contact your regional account manager or email; support.emea@solideu.com
SOLiD GENESIS and gGENESIS Platforms
SOLiD GENESIS n78 Sub3 DAS
SOLiD GENESIS n78 DAS
C1. High-Level Overview of GENESIS Portfolio (1 day)
Perfect for technical sales personnel or as an introduction to GENESIS. Available remotely or face to face.
C2. DMS3000 Monitoring Software System Overview (1 day)
Perfect for NOC personnel or remote monitoring engineers. Available remotely or face to face.
C3. System Architecture and Dimensioning (1 day)
Perfect for system and solution RF designers. NB: Not specific to design suite software. Includes an end of session exam resulting in a pass or fail mark. Available face to face.
C4. Hardware Installation & Commissioning GENESIS ( 2 days)
Perfect for installation and commissioning engineers. Includes an end of session exam resulting in a pass or fail mark. Course prerequisite: System Architecture and Dimensioning (1 day) or High Level Overview of GENESIS Portfolio (1 day). Available face to face only.
C5. Hardware Installation & Commissioning gGENESIS ( 2 days)
Perfect for installation and commissioning engineers.
Includes an end-of-session exam resulting in a pass or fail mark.
Course prerequisite: System Architecture and Dimensioning (1 day) or High-Level Overview of GENESIS Portfolio (1 day).
Available face to face only.
C6. GENESIS Operational Maintenance, Troubleshooting & Hardware Replacement (1 day)
Perfect for commissioning and maintenance engineers.
Includes an end-of-session exam resulting in a pass or fail mark.
Course prerequisite: C4 Commissioning GENESIS Portfolio (1 day) & C5 Commissioning gGENESIS Portfolio (1 day)
Available face to face only.
C1. High-Level Overview of GENESIS Portfolio (1 day)
Available remotely or face to face.
Abbreviated: GENESIS systems >3GHz
Course is conducted face to face during one working day, with lunch and refreshment breaks.
Main topics covered are;
General overview of GENESIS (Sub3GHz) and gGENESIS (n78)
System topology examples including main building blocks and connectivity.
Overview of all head-end and remote-end equipment. Overview of installation options.
Overview of system & capacity dimensioning.
C2. DMS3000 Monitoring Software System Overview (1 day)
Available remotely or face to face.
Course is conducted face to face during one working day, with lunch and refreshment breaks.
Main topics covered are;
Overview of DAS topology
Run through all DMS features and functions, including:
• DMS system setup and administration.
• DMS installation options: DMS3000Pro, DMS3000Lite, VirtualisedDMS
• Alarm management
• Network setup
• Logs
• Reports
• Troubleshooting
Review of DAS setup/commissioning menus
Discussion of possible alarm resolutions
C3. System Architecture and Dimensioning (1 day)
Available face to face only.
Course is conducted face to face during one working day, with lunch and refreshment breaks.
Main topics covered are;
Design focused review of the following
• GENESIS DAS head-end equipment
• GENESIS DAS hub equipment
• GENESIS DAS remote-end equipment
• GENESIS Signal framing and capacity capabilities
• GENESIS Review of system dimensioning
• gGENESIS DAS head-end equipment
• gGENESIS DAS remote-end equipment
• gGENESIS Signal framing and capacity capabilities
• gGENESIS Review of system dimensioning
End to end system link budget parameters
End of session exam
C4 Hardware Installation & Commissioning GENESIS (2 days)
Available face to face only
Course is conducted face to face during one working day, with lunch and refreshment breaks. *Please note there will be some overlap in topics each day.
Main topics covered are;
Brief review of GENESIS system dimensioning
Overview of connectivity
Component familiarization and capacity
Equipment requirements for environment
GENESIS DAS Set-up
GENESIS Initial set-up of the system using DMS and GUI
GENESIS Commissioning preparation (pre-commencement checks/design parameters
GENESIS Basic commissioning (signal input/routing/auto setup)
GENESIS Further commissioning (grouping/sectorisation/allocation/levelling)
GENESIS Optimisation & RF testing
End of session exam
C5. Hardware Installation & Commissioning gGENESIS (2 days)
Available face to face only
Course is conducted face to face during one working day, with lunch and refreshment breaks.
*Please note there will be some overlap in topics each day.
Main topics covered are;
Brief review of gGENESIS system dimensioning
Overview of connectivity
Component familiarisation and capacity
Equipment requirements for environment
gGENESIS DAS Set-up
gGENESIS Initial set-up of the system using DMS and GUI
gGENESIS Commissioning preparation (pre-commencement checks/design parameters)
gGENESIS Basic commissioning (signal input/routing/auto setup)
gGENESIS Further commissioning (grouping/sectorisation/allocation/levelling)
gGENESIS Optimisation & RF testing
End of session exam
C6. Operational Maintenance, Troubleshooting & Hardware Replacement (1 day)
Available face to face only
Course is conducted face to face covering two working days, with lunch and refreshment breaks. .
Main topics covered are;
Use of localised GUI (local user interface)
Logging into DAU or DMS locally on-site
Checks for issues/networking (Ethernet and system SFP)
Potential fault scenarios, and troubleshooting technique.
Alarm troubleshooting
Hands-on unit/component replacement
Maintenance overview
End of session exam
Terms and Conditions
Due to the nature of scheduling, all Purchase orders must be received by SOLiD in advance;
Online training –minimum 1 week before commencement of the course.
Training in the UK at our training location in Reading – minimum 2 weeks before commencement of the course.
Training remotely at site. PO must be received in advance of any booking
This is necessary for scheduling trainers and logistics for remote training. The lack of timely PO will result in the rescheduling of requested training.
Please do not hesitate to contact us to discuss the best way to structure your training needs at: support.emea@solideu.com using the subject ‘Training’
For overseas candidates, our training location in Reading may be best accessed by Heathrow Airport and the Elizabeth Train Line offers regular departures direct to Reading Central Station.
